Galvanized metal fence post are cheap, probably under $10 each. Be sure to use safety glasses chipping concrete. Also if you reuse them clean them up and repaint especially below ground since concrete is so acidic.

.

In this way, can you reuse old fence posts?

Re: Reusing old fence post holes Take a sledge, break the old concrete off the old post, save it, if the post is still good enough to reuse, great, use it.

Also Know, how do you fix a rise in a fence post? Fortunately, there is an easy vinyl fence repair for frost-heaved posts. Pull the posts out of the ground, and then dig the post hole deeper so it's below frost depth. (If you're doing this repair in winter, you may need special equipment to dig into frozen soil, such as a pickaxe or heater.)

Just so, how do you redo a fence post?

Steps

  1. Disconnect the post from any fence panels or wires.
  2. Dig a hole around 1 side of the fence post.
  3. Rock the post back and forth to break up the surrounding ground.
  4. Lift loose posts up by hand.
  5. Use a jack to remove your post if it's stuck.
  6. Clear the hole of any post and concrete remains.

How do you extend a wooden post?

How to Install Extended Posts on a Wood Fence

  1. Measure and cut a 4-by-4-inch extension post to the desired length.
  2. Cut two sections from the 1-by-4-inch lumber to act as braces for two sides of where the old post and extension will be joined.
  3. Cut two braces from the 1-by-6-inch lumber to match the lengths of the other two braces.

Related Question Answers

How do you get a post out of the ground?

Steps
  1. Tie your rope several times around the end of the plank.
  2. Tie the other end of the rope several times around the base of the T post, as close to the ground as possible.
  3. Set up your fulcrum about 6 inches (15.2 cm) from the base of the T post, and put the plank on top of it.
  4. Push down on the far end of the plank.

How do you take down a fence?

To remove the fencing and reduce everything to a frame, use your hammer on each piece of fencing, first to know the wood away from the frame, then use the claw end to pull out the nails. Stack the pieces of fence. Once you've finished you'll be left with horizontal pieces of wood and the vertical fence posts.

How do you remove a chain link fence post from the ground?

Getting it Out of the GroundClip the metal rings or strips holding the chain link to the posts and roll up the fencing. Lift off the top rail and caps. Dig down along the side of the concrete until you get to the bottom of the post and concrete. Wiggle the post back and forth.

Can you cut chainlink fence in half?

Of all the steps involved in installing a chain-link fence, cutting the fence to length is one of the easiest. You can cut the chain-link fence without physically cutting the woven "fabric" that makes up the majority of the fence. The secret to cutting your chain-link fence lies in the way the fence fabric is created.

How do you stretch a chain link fence?

How to Stretch a Chainlink Fence
  1. Roll out the chain-link mesh against the fence frame starting at one corner post.
  2. Hold the tension bar in place along the pole and fasten to the pole with brace bands spaced 1 foot apart.
  3. Stretch the mesh out between the corner posts with a pulling rod.
  4. Hook one end of a come-along to a brace band on a corner post.

Do you have to use concrete for fence posts?

Concrete is the most secure material for setting fence posts, especially if you have sandy soil. Gravel may be okay with dense, clay-heavy soil, but in looser soil, concrete is the only thing that will truly keep your fence posts stuck in place.

How much does it cost to remove fence posts?

The cost to remove your fence will depend mainly on the type of fence you have, the size of it, and the contractor you choose. On average, you can expect to pay around $1 - $2.50 per foot of fence to be removed. However, some fences can reach upwards of $10 - $12 per foot.

What is a post puller?

Definition of post puller. An electric vehicle having a powered drum for handling wire rope used to pull mine props after coal has been removed; used for the recovery of the timber.

How do you remove T bar fence posts?

Begin by rocking the post back and forth to loosen the soil around it.

Option 1

  1. Position a fence post puller next to the T-post to be removed.
  2. With the post puller arm end up, latch the puller's hook beneath one of the nodules on the T-post.
  3. Push the puller arm down slowly and allow the leverage action to do the work.

How do you install an aluminum fence gate?

How to Install an Aluminum Gate
  1. Step 1 Digging the Holes for Your Gate Post. The first thing you want to do when installing your gate is dig the holes for the gate post.
  2. Step 2 Concreting Your Gate Post. You have dug your holes and tossed the post inside them.
  3. Step 3 Hanging Your Gate & Installing Hardware.